MelPump › Compatibility › Ebac › H1A05WG
EB
Ebac H1A05WG
Select an integration method below to see supported data points and features.
Monitored data points
Parameters available in the MelPump dashboard and reports. The "Control" column shows if you can also change the value from the app.
| Parameter | Description | Monitor | Control |
|---|---|---|---|
| COP | Efficiency ratio - heat output divided by electricity input | check_circle | remove |
| Compressor Frequency | Speed of the compressor in Hz, higher values mean more heating or cooling power | check_circle | remove |
| Compressor Frequency | Speed of the compressor in Hz, higher values mean more heating or cooling power | check_circle | remove |
| Condensing Temp | Internal heat pump temperature where refrigerant releases heat to the water system, higher values usually mean lower efficiency | check_circle | remove |
| Delta Temp | Difference between the water leaving and returning to the heat pump, used to show how much heat is being transferred | check_circle | remove |
| Target Tank Water Temp | Desired domestic hot water tank temperature | check_circle | tune |
| Tank Water Temp | Current temperature of the domestic hot water stored in the tank | check_circle | remove |
| Target Tank Water Temp | Desired domestic hot water tank temperature | check_circle | tune |
| Input Power | Estimated electrical power being consumed | check_circle | remove |
| Output Power | Estimated heat energy being produced | check_circle | remove |
| Brine Inlet Temp | Temperature of the ground loop fluid entering the heat pump | check_circle | remove |
| Brine Outlet Temp | Temperature of the ground loop fluid leaving the heat pump | check_circle | remove |
| Fan 1 RPM | Speed of the first outdoor unit fan | check_circle | remove |
| Error Code | Diagnostic code shown when there is a problem | check_circle | remove |
| Has Error | Indicates if the system has an active error | check_circle | remove |
| Compressor Frequency | Speed of the compressor in Hz, higher values mean more heating or cooling power | check_circle | remove |
| Flow Rate | Amount of water flowing through the system in litres per minute | check_circle | remove |
| Flow Rate | Amount of water flowing through the system in litres per minute | check_circle | remove |
| Target Temp #1 | Target water temperature for the heating circuit in zone #1 | check_circle | remove |
| Indoor Temp #1 | Current air temperature in rooms served by heating zone #1 | check_circle | remove |
| Thermostat Temp #1 | Desired room temperature set for heating zone #1 | check_circle | remove |
| Operation Mode #1 | Operating mode for heating zone #1. In most heat pumps this is either constant flow or compensation curve mode, but some models may support advanced modes like auto-adaptation. | check_circle | tune |
| Return Temp | Water temperature returning to the heat pump from the heating system | check_circle | remove |
| Operation Mode | Current mode: heating, cooling, or hot water production. May also show other modes like antifreeze or legionella. | check_circle | tune |
| Operation Mode | Current mode: heating, cooling, or hot water production. May also show other modes like antifreeze or legionella. | check_circle | tune |
| Outdoor Temp | Current outside air temperature measured near the heat pump | check_circle | remove |
| Fan 1 RPM | Speed of the first outdoor unit fan | check_circle | remove |
| Flow Temp | Water temperature leaving the heat pump and going into the heating system | check_circle | remove |
| Target Temp #1 | Target water temperature for the heating circuit in zone #1 | check_circle | remove |
| Liquid Line Temp | Temperature of the liquid refrigerant flowing through the heat pump's cooling circuit | check_circle | remove |
| Lev A | Electronic expansion valve opening position | check_circle | remove |
| Lev A | Electronic expansion valve opening position | check_circle | remove |
| Power | Whether the heat pump is turned on or off | check_circle | remove |
| Indoor Temp #2 | Current air temperature in rooms served by heating zone #2 | check_circle | remove |
App-level features
Automation and optimization modes that MelPump unlocks for this integration.
bolt
Solar Mode - Zone Heating
bolt
Advanced Scheduler
bolt
Push and Email Notifications
bolt
Energy Estimation